1992 Evinrude TE115TLEND Pee Hole 115HP 2 stroke

[GatorbOi334]

I have a hose for a water pump drain. Problem is it's not connected to anything and I don't see anywhere to connect it on the motor. There is no water draining from the inside the motor housing anywhere. Does anyone know where this hose connects and...

[Wheelman81]

Engine bogging and sometimes dies after running over 10 or 15 minutes at 3000 rpm . Engine will run fine all day long at low cruising rpms (under 3000). I have changed water separator and drained and refilled fuel tank and new plugs and wires oil change...

[Wheelman81]

Hello fellow boaters! I have a 97 bayliner 5.7 liter with merc. outdrive.This boat has never been in salt water. I have been having this problem with the boat bogging down to an idle (and dying if I try to run it faster after it has bogged) in the last...

[Markoku]

Hello,
I've recently come into a 1975 Evinrude 115hp outboard. This motor had not been started since 1996. I got it started (cleaned carbs, new sparks) and it runs great now. I'm new to Evinrude's, but I'm conceded that it might not be cooling

[jake_A.S.24]

hi, i recently purchased a boat that has a 1969 chrysler 55 horse outboard engine. The Model number is 5575 and serial number is 1722.

I just want to say that i am pretty new to the boat engines, but i have a good general knowledge of motors....

[AAusbro51]

This is my first post after creeping around the forum for a good month. This is a very very very cool and helpful site you have here. Thank you for all the knowledge and expertise! I am a new (to me) boat owner and I'm just about as green as it gets....

[81Bronco]

Finally created an account, but anyways, thought I would see if i could get some help on my motor. I am attempting to replace the water pump on my johnson, but i'm unable to gain enough room to disconnect the shift linkage from the bottom unit....

[bamabutch90]

1997 Evinrude 115 (E115SXEUA) mounted on a 1992 Centrury 1800 Center Console, I ONLY run 100% fuel, Quick Silver 2 stroke oil (pre-mix), Quick Silver gear oil.

119-120 compression on the cylinders

My Problem:
3.5 years...

[pmp1986]

Hi, friends,
Not fluent in Engish, but i'd try to explain )
Last time boating i got a problem. At one of 4.3 engines one of exhaust elbows got a temperature separation: it's left side was like in fewer but the other one
was cold. I've...

[TheGeek]

Hello, would anyone know the torque specs for the water pump housing nuts and bolt in the lower unit of an '73 850 85 hp motor?

Thank you.

[cmckinney]

Hello everyone my name is chase I bought my first boat about a month ago and it is a 1987 wellcraft 190 with the 165 4 cyl. I had to replace the impeller in the outdrive. I got it switches out put the new impeller in the housing then put everything...

[kybanker]

Hello all:

I am attempting to replace the water pump on my 1984 Johnson 40hp outboard for the first time (it has always been done by a boat mechanic previously). I have removed the bolt below the trim tab, as well as the 4 bolts securing...

[kippstakes]

My engine hasn't been pumping water correctly. Impeller works fine (just installed a new one), and it is definitely a thermo problem- actually this engine model uses a Vernatherm valve. Thing is, there is NO way the thermo housing is coming off, and...

[hhbanks]

Hey everyone,

I have a 1971 Evinrude Sportster 25.
It is fine for about 10 - 15 minutes of running at full throttle, but then it stops pumping, overheats, and shuts off.

I imagine the pump is fine since it pumps properly...

[icedogs66]

Hey guys i am not sure what I did wrong. replaced the water impeller put unit back together and now wont shift out of forward. I put the unit in forward prior to starting the disassembly any ideas?

[bigjake6]

I need some help, my motor started blowing white smoke, it is not overheating and I have tried adjusting the 50:1 fuel mixture in very small amounts, to no avail the only thing I can think is I have read about water getting in the engine. I have checked...

[bassboy416]

Bought seloc manual and sierra replacement kit (gaskets and impeller without housing or base). While researching the procedure on this the manual confused me more than it helped. First, it is unclear how it all comes apart and what linkage might need...

[lwyatt]

Hello all I am new to the forum and have done my best to try and find answer before I posted but could not.

I have a 89 Evinrude 110hp have removed the vro pump about 1 year ago
lately the warning buzzer is going off I have verified...

[99FourWinns]

Hi everyone I am new to this, so I hope I am posting correctly. I recently acquired a 99 Four Winns horizon 170 with a 4cyl Volvo penta I/O. An inspection report was done, and I wanted to a get a little help on finding a solution to some of the issues....

[GearFly]

Changed the water pump impellor, gaskets, and lower unit oil and ran the motor. Shifted the engine at idle to make sure that all was well. Now the shift lever clicks/grinds slightly when I put it in reverse. When changing The pump case gasket I toggled...

[rolltider1989]

Hello I have a 1998 50 hp force by mercury marine and I just replaced the water pump and took it too the lake and it's just spitting water out the back it's not a steady steam or flow is this normal?

[davostessco]

I have just rebuild this 40hp 4stroke and its running sweet apart from its not pumping water properly all the time so its got a new water pump impeller and kit through it .
so I take the thermostat out and start it with water connected and if...

[acdc96]

I just finished putting the bellows on my alpha drive and turn the engine over to make sure their is no bad clunks and the water circulating pump did not turn (idk if it's frozen) wen I turned the engine over before I took of the drive off it moved freely....

[leegoldring]

Complete Water Pump change out for 1969 1C. Removed gear assembly and pump top. Not only is the pump base stuck, it's aluminum, not plastic, I as would have expected. I certainly have not heard of any water pump bases being aluminum, and my only guess...

[tombgd501]

I have searched and searched with no luck on this. All I am trying to do is replace the water pump and this has turned in to a huge project. I need some guidance from you guys. I removed the lower unit by disconnecting the linkage through the intake...